The aggregates should therefore have sufficient toughness to resist their disintegration due to impact. This characteristic is measured by impact value test. The aggregate impact value is a measure of resistance to sudden impact or shock, which may differ from its resistance to gradually applied compressive load. Procedure of Aggregate Impact Test.
Aggregate crushing value test on coarse aggregates gives a relative measure of the resistance of an aggregate crushing under gradually applied compressive load. Coarse aggregate crushing value is the percentage by weight of the crushed material obtained when test aggregates are subjected to a specified load under standardized conditions.
“Aggregate Crushing values is a relative resistance of aggregates to crushing under gradually applied compressive load” In situations, when aggregate value 30 or higher the result may be a mistake and in such cases, the “ten percent fines value” should be determined and used instead.
Concept and significance of the Aggregate crushing value test. The ‘ aggregate crushing value test ` gives a relative measure of the resistance of an aggregate to crushing under a gradually applied compressive load. Aggregate crushing value is defined as the percentage by weight of the crushed (or finer) material obtained when the test aggregates are subjected to a specified load under
This test helps to determine the aggregate crushing value of coarse aggregates as per IS: 2386 (Part IV) 1963. The apparatus used is Cylindrical measure and plunger, Compression testing machine, IS Sieves of sizes 12.5mm, 10mm and 2.36mm. i) The aggregates passing through 12.5mm and retained on 10mm IS Sieve are oven-dried at a
Objective Of Aggregate Crushing Value Test. May 08 2013 · Aggregate Crushing Value Test Appratus Preparation of sample Test sample consist of aggregate passing a 125mm IS sieve and retained on a 10mm IS sieve The aggregate to be tested is dried in oven for a period of not less than 4 hours Procedure
Mar 24, 2013· This feature is not available right now. Please try again later.
Objective: 1. Determine the aggregate crushing value of coarse aggregate. 2. Assess suitability of coarse aggregates for use in different types of road. Theory: The " aggregate crushing value " give a relative measure of the resistance of
Sep 12, 2015· Crushing Test Fig-1 Crushing Test Setup. One of the model in which pavement material can fail is by crushing under compressive stress. A test is standardized by IS: 2386 part-IV and used to determine the crushing strength of aggregates. The aggregate crushing value provides a relative measure of resistance to crushing under gradually applied
The aggregates should therefore have sufficient toughness to resist their disintegration due to impact. This characteristic is measured by impact value test. The aggregate impact value is a measure of resistance to sudden impact or shock, which may differ from its resistance to gradually applied compressive load. Procedure of Aggregate Impact Test.
The aggregate crushing value test result should not be more than 30 % for the concrete used for roads and pavements and, in case of other structures; it may be permitted up to 45%. (c) Standard Guidelines for Crushing Test: Followings are the standard guidelines for the crushing test on aggregates:
Mechanical Properties of Aggregates Aggregate Crushing Value Test (BS:812, part 3) Procedure • The material to be tested should pass a 14.0 mm (1/2 in.) sieve and be retained on a 10 mm (3/8 in.) sieve. • Dry the sample in an oven at 100-110 0 C for four hours. • Place the sample in a standard cylindrical mould and tamp it. • Put a plunger on the top of the aggregate and place the
This test helps to determine the aggregate crushing value of coarse aggregates as per IS: 2386 (Part IV) 1963. The apparatus used is Cylindrical measure and plunger, Compression testing machine, IS Sieves of sizes 12.5mm, 10mm and 2.36mm. i) The aggregates passing through 12.5mm and retained on 10mm IS Sieve are oven-dried at a
Objective Of Aggregate Crushing Value Test. May 08 2013 · Aggregate Crushing Value Test Appratus Preparation of sample Test sample consist of aggregate passing a 125mm IS sieve and retained on a 10mm IS sieve The aggregate to be tested is dried in oven for a period of not less than 4 hours Procedure
May 08, 2013· Objective For determination of the aggregate crushing value of coarse aggregate, which passes 12.5 mm. IS sieve and retained on 10 mm. IS sieve. Reference Standard IS: 2386 (Part IV)-1963 Methods of test for aggregate for concrete Part IV Mechanical Properties. Equipment & Apparatus Steel Cylinder Sieves (12.5mm,10mm) Cylindrical metal measure Tamping Rod Balance (0
Calculate Aggregate Crushing Value. The ratio of the weight of fines formed to the total sample weight in each test shall be expressed as a percentage, the result being recorded to the first decimal place: Aggregate Crushing Value = W B W A × 100. Where, W A is weight of surface-dry sample
Jun 13, 2019· The crushing value of aggregate is very important to know the strength of the aggregate. For finding the resistance of aggregate under gradually applied compressive load, the crushing value test of aggregate is done. For the crushing value test, the following procedure is followed. Procedure for finding the crushing value of aggregate.
For the Aggregate crushing value test, an aggregate sample passing through 12.5 mm IS sieve and retained on 10mm IS sieve is selected and dried to a temperature of 105 ºC to 110 ºC then cooled to room temperature.
Ordering info 48-D0510 ACV Aggregate crushing value apparatus, 150 mm dia. 48-D0511 ACV Aggregate crushing value apparatus, 75 mm dia.
Jan 23, 2018· AIM: To determine the aggregate crushing value of coarse aggregates as per IS: 2386 (Part IV) 1963. APPARATUS: i) Cylindrical measure and plunger ii) Compression testing machine iii) IS Sieves of sizes 12.5mm, 10mm and 2.36mm PROCEDURE: i) The aggregates passing through 12.5mm and retained on 10mm IS Sieve are oven-dried at a
Apr 10, 2012· Aggregates used in the construction, should be strong enough to resist crushing. If the aggregates are weak, the stability of the structure is likely to be adversely affected. The strength of coarse aggregates is assessed by aggregate crushing test. The aggregate crushing value provides a relative measure of resistance to crushing under gradually applied compressive
Calculation of aggregate crushing value. The aggregate crushing value is defined as the ratio of the weight of fines passing through specified IS (here 2.36mm sieve) to the total weight of sample expressed in percentage. W1= Weigh of the total aggregates (Wa-We) W2= Weigh of aggregates passing through 2.36mm IS sieve.
Aggregate Crushing Value Apparatus Ask Price Specifications : Consists of MS cylindrical container 150 mm t 0.5mm diameter x 130mm to 140mm high with base plate 200 to 230 mm/sqr x 6mm thick plunger of 148mm + 0.5mm diameter x 100 to 115 mm high
The aggregate crushing value test result should not be more than 30 % for the concrete used for roads and pavements and, in case of other structures; it may be permitted up to 45%. (c) Standard Guidelines for Crushing Test: Followings are the standard guidelines for the crushing test on aggregates:
Mechanical Properties of Aggregates Aggregate Crushing Value Test (BS:812, part 3) Procedure • The material to be tested should pass a 14.0 mm (1/2 in.) sieve and be retained on a 10 mm (3/8 in.) sieve. • Dry the sample in an oven at 100-110 0 C for four hours. • Place the sample in a standard cylindrical mould and tamp it. • Put a plunger on the top of the aggregate and place the
Jun 13, 2019· The crushing value of aggregate is very important to know the strength of the aggregate. For finding the resistance of aggregate under gradually applied compressive load, the crushing value test of aggregate is done. For the crushing value test, the following procedure is followed. Procedure for finding the crushing value of aggregate.
Procedure of Aggregate Impact value test. The test sample: normally aggregates sized 10.0 mm to 12.5 mm. the aggregates should be dried by heating at 100-110 0C for a period of 4 hours and cooled.
Jan 23, 2018· AIM: To determine the aggregate crushing value of coarse aggregates as per IS: 2386 (Part IV) 1963. APPARATUS: i) Cylindrical measure and plunger ii) Compression testing machine iii) IS Sieves of sizes 12.5mm, 10mm and 2.36mm PROCEDURE: i) The aggregates passing through 12.5mm and retained on 10mm IS Sieve are oven-dried at a
Apr 10, 2012· Aggregates used in the construction, should be strong enough to resist crushing. If the aggregates are weak, the stability of the structure is likely to be adversely affected. The strength of coarse aggregates is assessed by aggregate crushing test. The aggregate crushing value provides a relative measure of resistance to crushing under gradually applied compressive
Calculation of aggregate crushing value. The aggregate crushing value is defined as the ratio of the weight of fines passing through specified IS (here 2.36mm sieve) to the total weight of sample expressed in percentage. W1= Weigh of the total aggregates (Wa-We) W2= Weigh of aggregates passing through 2.36mm IS sieve.
The aggregate crushing value provides a relative measure of the resistance of an aggregate to crushing under a gradually applied compressive load. The oven dried and accurately weighed aggregates are subjected to crushing test on compression testing machine and
BS 812 part 110 describes a method to determine the aggregate crushing value (ACV) which gives a relative measure of the crushing resistance of aggregate under an increasing compressive load.The method is applicable to aggregates passing a 14.0 mm test sieve and retained on a 10.0 mm test sieve.
May 04, 2020· The crushing strength or aggregate crushing value of a given road aggregate is found out as per IS-2386 Part- 4. The aggregate crushing value provides a relative measure of resistance to crushing under a gradually applied compressive load. To achieve a high quality of pavement aggregate possessing low aggregate crushing value should be preferred.
Feb 08, 2012· Aggregate impact and crushing test 1. Impact, 10% Fines & Crushing Tests NANYANG TECHNOLOGICAL UNIVERSITY School of Civil and Structural Engineering LABORATORY PAVEMENT MATERIALS AGGREGATE IMPACT TEST, TEN PERCENT FINES TEST AND AGGREGATE CRUSHING TESTOBJECTIVESTo assess the resistance of an aggregate to mechanical degradation by theAggregate Impact Test, Ten Percent Fines Test and Aggregate
The apparatus of the aggregate crushing value test as per IS: 2386 (Part IV) 1963 consists of: 1) A 15cm diameter open ended steel cylinder with plunger and base plate, of the general form and dimensions as shown in Fig 1. 2) A straight metal tamping rod
number. Report the mean as the Aggregate Crushing Value, unless the individual results differ by more than 0.07 times the mean value. In this case repeat the test on two further specimens, calculate the median of the four results to the nearest whole number and report the median as the Aggregate Crushing Value. A data sheet is given as Form 7.7.1.